Twin Fuselage
in
3D Modeling Design
held by
UASCA
Last seen:
Contest Closed
-
Open
-
Choosing Finalist
-
Ended
Description:
I need a 3D CAD file of a conceptual twin fuselage or twin tail aircraft similar to the images attached. The wing span will should be about 7 feet long. This should not have a cockpit, or mufflers, scoops (unless require) as this will be an electric aircraft concept.
Wants:
A thought out design that looks good.
Don't Wants:
Someone else s design
Software:
- SolidWorks 2015 or similar
Payment PendingEntries
Discussion
Hi there,
Unfortunately the contest was closed, at buyer's request. Also, all recent comments have been deleted.
@REDA: You can't force the buyer to prepay the contest. You can work only on prepaid contests, if that's an inconvenience for you. And note that he had a prepaid contest last year: https://www.cadcrowd.com/contest/1089-transport-uas-uav-drone
@UASCA: If you want to reopen the contest anytime, let me know.
Thanks,
Lucian
Unfortunately the contest was closed, at buyer's request. Also, all recent comments have been deleted.
@REDA: You can't force the buyer to prepay the contest. You can work only on prepaid contests, if that's an inconvenience for you. And note that he had a prepaid contest last year: https://www.cadcrowd.com/contest/1089-transport-uas-uav-drone
@UASCA: If you want to reopen the contest anytime, let me know.
Thanks,
Lucian
ATTENTION ALL: This contest is now cancelled. DO NOT submit any more designs. Apparently we have a few bad apples who want to discuss things in an open forum that are not applicable.
PilotJeffEdwards, thanks for your comments. I would appreciate if you kept comments related to the design requirements requirements.
You're going to want to make the payment prepaid for more designs.
@UASCA,
Thanks for your to the point answer.
Regards,
Rupak B
Thanks for your to the point answer.
Regards,
Rupak B
Any software I can open in Solidworks 2015
Rupak: 7 Foot total for three Wings... left wing, center wing and Right wing. I hope this helps
Pankaj: Autocad 2016 is fine
MichaelHS: It is conceptual to develop a prototype to test functionality.
Pankaj: Autocad 2016 is fine
MichaelHS: It is conceptual to develop a prototype to test functionality.
Dear Buyer,
"The wing span will should be about 7 feet long", means each wing span will be 7' or all total 7' (i.e. 3.5'+3.5') for both the wings?
Regards,
Rupak B.
"The wing span will should be about 7 feet long", means each wing span will be 7' or all total 7' (i.e. 3.5'+3.5') for both the wings?
Regards,
Rupak B.
Can i make it in AutoCAD 2016?
Are you looking for a concept for eventual production? Will you need any performance analysis?
Thanks
Michael
Thanks
Michael
Anything that I can use or convert with Solidworks 2015 please.
Hello,
Would you need it in a particular software done, or any software?
Thanks
Mark
Would you need it in a particular software done, or any software?
Thanks
Mark
Similar Contests on Cad Crowd
2D to 3D conversion
Convert 2D drawing set to 3D set. Deliverable's shall include individual part files for each part (flange, support and curl) and an assembly file (of the complete assembly).
2D Drawings (100)
Produce a 100 drawings following the procedure to the letter. Make sure to review the procedure since it changed slightly since last time
Best 75% Mechanical Keyboard
Description:
SEE BRIEF DOCUMENT
Design the perfect 75% mechanical keyboard, paying close attention to the case. The keyboard case should be unique, high profile and the same colour as the space grey Macbook Pro. Subtle Curves and rounded edges may be effective.
Wants:
SEE WORD DOCUMENT
• Aesthetic quality and overall sleekness of case.
• Detail/ realism of render
• Creativity/ innovation of design.
• Ergonomics.
• Capacity for the case to fit a printed circuit board.
Don't Wants:
SEE BRIEF DOCUMENT
• Models that do not allow any space for a printed circuit board.
• Something that’s already on the market.
Software:
CAD
Hypophonia Amplification Device
I have Parkinson's disease. One of the classic symptoms of Parkinson's is hypophonia, a decrease in speech amplitude. My hypophonia is severe and presents a challenge to me in terms of job, family, & friends. I am seeking a small, discreet, and aesthetically pleasing personal amplification device. Here are some criteria.
-The microphone should be sensitive as my hypophonia is severe.I'm not averse to a handheld microphone that I bring to my mouth as needed.
-I would like an on-off switch on the microphone.
-I prefer regular batteries to rechargeable batteries
-The speaker should be small and have volume control. I would like to be able to use it for one-on-one conversation as well as in meetings or when lecturing.
-it would be great if the speaker could be placed somewhere nearish to where the sound naturally comes from, i.e., my mouth. E.g. the collar of the shirt or pinned to the shirt pocket. Attached to the belt is also possible.
-Would be nice if the speaker could be removed and put on the table for meetings
-All three pieces (mic, speaker, amplifier) can be separate so no one is too bulky
Custom funnel with integrated phone mount
Design a 3d model so that a prototype can be injection molded and/or 3d printed. Must come with all necessary components to render the prototype.
Lucian
Administrator