Vending Machine CAD Design

in New Invention Development held by Wills
Contest Closed
Description:
I have a sketch of vending machine, which needs to be converted into CAD design with accurate measurements.
Wants:
Design details
Don't Wants:
Delay in project
Software:
  1. AutoCAD

Entries

No Entries Submitted Yet.

Discussion

No Comments Submitted Yet.

Similar Contests on Cad Crowd

new bottle
place logo on 3D dishsoap bottle - by a kitchen sink
Drinking Bottle
Drinking Bottle with special design
Balloon Archery Target
Balloon Archery Target - Basically a device that holds 4 balloons in a target like fashion to make target shooting for kids more enjoyable. My son and I recently discovered archery. While he is motivated to go and shoot arrows, we experienced a turning point when we started to use balloons as opposed to paper targets. I realized that there is something to having more exciting feedback for the kids. However, even a regular balloon filled to capacity was hard to hit and it was difficult to tell how well you aimed. The device I would like to design uses 4 balloons, widens the target and also provides visual feedback for accuracy. Terminology: 4 inch round ballon These are technically 5 inch balloons but would only inflate to 4 inch for our purpose. http://www.amazon.com/gp/product/B007AMUJ16/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 260 Balloons Your basic balloon animal balloon. Can be inflated to any length. Inflated they are about 1.75 inches wide. http://www.amazon.com/260-Q-Balloons-Qualatex-Royal-Magic/dp/B000SDPYMS Attachment The mechanism to attach the entire holder/device to the target backer. This should consist of a hole that is large enough to accommodate a pencil. In most cases a thick nail ~5mm would be used to loosely attach the holder/device to the target backer. As an alternative, a simple hole could be used with a loop wire (like a key ring) to pass a nail through. Target backer Usually a large bail of hay, dense styrofoam or extra large bag filled with dense material. Holder/Device The part we need to make that holds the balloons in place and attaches to the target backer. Goals: Easy to ship (i.e. flat). Easy to assemble (i.e. minimal parts). Durable but as thin as possible when looking directly at the unit. Imagine arrows being fired at this and the thinner the profile head on, the less likely arrows will actually do damage. 3D printer friendly for initial launch. If successful will goto mold. Technical needs: I'd like to keep the balloons as close together as possible, but it isn't critical that they touch. Obviously there will be some variance based on the balloons and how they are inflated. Remember this is for kids, not olympic archers. Fun feedbacl, ease of use (adults will need to setup for the kids) and simplicity are more important than tolerances. Description of Holder/Device 1 Middle bracket/arm holding a single 4 inch round balloon 3 concentric circles each holding a 260 type balloon (various lengths depending on which circle). Inflated they are about 1.75 inches around. The entire back of the target should lay flat. This means that the 4 inch round balloon will stick out further than the 260 balloons. The holder/device should be made up of exactly two pieces that will allow for easier 3D printing and shipping. The physical connection between the two can either be built into the model with a turn and snap or simply allow for a screw/nut to be used. If screw and nut, the design should include a feature that only allows the two pieces to come together in one way so there is no question how the user should assemble. All balloons will be inflated and tied to the appropriate size by the user before being inserted into the holder/device. The 260 balloons will also be tied in a "circle" before being inserted into the holder/device. All connections between the holder/device are press fit. All parts of the holder/device need to avoid sharp edges to ovoid popping balloons. The attached picture shows the concept but without any type of holder. They are press fit together and are more out of shape than round. The holder/device should greatly improve the roundness of the balloons when properly in place. The attached drawing shows some very basic 2d drawings. However, if you have a better concept for holding the balloons, I am open to that. This is really function over form (i.e. emphasis on working over how it looks as a standalone product.)
3D Printed Box
Need an open topped box to print (7.5" x 2.5" x 1.5" tall); top is open; also print flat part (7.5" x 2.5") that ideally can snap onto the open box; will need holes cut into bottom of box, but dont know size yet; will need logo etches on bottom of box.
Leather bag design
We have multiple product design needs over July-August. To start with we're looking for a 3d render of a bag similar to this: http://www.katespade.co.uk/uk/cameron-street-candace-satchel/invt/pxru5931-001 but with a a pattern design overlayed) (see attached basic ideas and mock ups) interior lining to match exterior Gold detail change to silver. Top label on bar to say Adele Chase in raleway font.