Installation of Solar Panels on Train Railways

in Mechanical Engineering held by aigarss
Contest Closed
Description:
We would like to find a consultant, who could solve the following issues:
- identify problems
- find solutions
- design product
- make prototype
Wants:
Previous experience creating products
Strategic, critical and solution oriented thinking

Entries

No Entries Submitted Yet.

Discussion

No Comments Submitted Yet.

Similar Contests on Cad Crowd

Design
A keyless, codeless Padlock. Contains non-functioning keyhole, or code-combo rows to give the appearance of a standard metal Padlock. To OPEN/UNLOCK it, it is squeezed together until "click" is actuated, then pulled open. To CLOSE/LOCK, it is squeezed together as per standard Padlock.
Hook Design for SNUZR: The World's First Toilet Stall Hammock
Looking for an engineer who can design a wall grappling hook that can suspend a hanging chair hammock between two partition walls in a toilet stall. The chair hammock has 4 straps which are attached to 4 identical wall hooks affixed at the top of the toilet stall partition. The hook must be able to hold securely in place as load weight is gradually applied. The typical user will install the hammock as follows: attach hooks on the side partition walls of the toilet stall - towards the front and back of stall and on both sides, attach hammock straps onto the hook, sits down on the hammock and if necessary get back up to adjust straps to ideal chair height and position. Previous designs of the hook did not stay in place and slid towards the centre of the wall due to side torque as weight was applied via the straps at roughly 45 degree angles (which also damaged or marked up the walls). We need a rockstar engineer who can solve this design challenge with a sense of humour.
4 DoF mechanical arm mounted on a tripod
We want to design an arm which can be mounted on a tripod as shown in the attached image. The total length of the arm is going to be 1.5m from pivot to end effector. For the movement of the joints please refer the other image. The total weight of the arm and the mechanism has to be less than 3kg. The payload is going to be less than 300 grams. Your job is to design the underlying mechanism which can drive this arm as smoothly as possible. The deliverables are going to be CAD of the mechanism and BOM and anything else which will be required to prototype the arm. The project will only begin with this contest and the designer will be hired for continuation of the project.
Roller Mop
This is for a new mop invention. I was able to make a somewhat functioning scaled model of just the internal mechanisms as seen in the attached video. Taking from the carpet sweeper seen here: http://bit.ly/32vqkGF, I want it to have 3 sponge rollers that spin in alternate directions at an accelerated speed (3:1) so that when it is pushed across the floor, the sponge rollers spin to mop up a mess. I used gear pullies to spin the rollers, however, I am open to any kind of gears based on your expertise for efficiency, durability, efficacy, and cost of goods. This will be a retail product and I would like to keep the price competitive with sweepers. Please provide the following: - Completed product with retail-ready design - Full size (similar to the carpet sweeper) - Rollers should have push pin or equivalent to easily pop rollers in and out (they will be replenishments with a variety of roller options (i.e. brillow, sponge, brush, shammy, etc.) - It should break down to fit into a retail box, again similar to the carpet sweeper link provided. - Rollers are 1" diameter - Wheels are 2"
4th & 5th Axis Holder Design
This contest is for a 4th & 5th Axis Holder that will house two dental ceramic discs. We will provide the 2 motor design files, so you can build based on the motors. The preferred design will have a Gimbal "Like" Design. This holder will not be using any gear drives or planetary gear drives, The motors will be directly connected to the holder. There will be 2 parts to this holder: 1. The holder that is connected to the 2 servo motors. 2. The Holding Plate that will attach to the holder which holds the material. Key points of the holder: 1. The holder needs to have a function that allows an interchangeable Holding Plate for different types of materials